Stars and Stripes Safety and Efficiency Agreement

1 Precision Furnace Tune-Up

img
Benefits

      • Lower utility bills.
      • Extended equipment life.
      • Fewer repairs, breakdowns, and improved system reliability.
      • Peace of mind for you and your family.
      • Increased heating capacity.

Also, 1 Precision Air-Conditioning Tune-Up

img
Benefits

    • Lower utility bills by reducing energy consumption and waste.
    • Extended equipment life.
    • Peace of mind for you and your family.
    • Fewer repairs, and improved system reliability.
    • Increased cooling capacity and efficiency.

Our Exclusive Precision Tune-Up Procedure Includes

  1. Inspect and tighten all electrical connections and terminals.
  2. Clean, and adjust main gas burners.
  3. Clean, and adjust ignition/pilot assembly.
  4. Inspect heat-exchanger(s) & combustion chambers for cracks, rusting, or problem areas.
  5. Vacuum out blower compartment; return airdrop, and surrounding area. (No duct cleaning)
  6. Inspect the flue assembly and test flue gas drafting mechanism.
  7. Test and inspect all furnace safety controls.
  8. Test, record, and adjust gas pressure.
  9. Replace or clean standard air filters.
  10. Lubricate all fan motors and all moving parts.
  11. Measure and adjust blower for correct airflow.
  12. Adjust all dampers and set proper blower speed(s). No air balancing.
  13. Clean, level, test, and calibrate thermostat.
  14. Measure and record heating system output.
  15. Inspect and test thermocouple output as well as pilot safety switch.
  16. Measure and record electrical voltage, amperage, and component resistance.
  17. Inspect and test all system transformers, relays,contactors, and controls. Measure performance
  18. Repair minor air leaks in plenum and return airdrop.
  19. Advise customer on other ways to reduce energy consumption, improve safety and enhance comfort.
  1. Clean and thoroughly wash condenser coil(s).
  2. Wash and level condensing unit for proper motor and bearing wear.
  3. Lubricate motor and fan bearings as well as other moving parts as necessary.
  4. Clean and inspect evaporator coil and drain pan when readily accessible.
  5. Inspect condensate drain lines and fittings.
  6. Clean, level, and calibrate thermostat.
  7. Adjust and thoroughly clean blower motor and fan assembly as needed.
  8. Inspect, tighten and test all electrical connections. This includes disconnect switch.
  9. Inspect all cooling system electrical wires, connectors, and terminals.
  10. Test system starting and running capacitors.
  11. Test all controls, switches, relays, transformers, contactors, motors, and fans.
  12. Measure starting and running amperes, line voltage, and control voltage.
  13. Test system-starting capabilities.
  14. Test system for proper airflow and air delivery.
  15. Inspect and adjust all safety controls.
  16. Monitor refrigerant (Freon) pressures and temperatures.
  17. Test and record super-heat and sub-cooling.
  18. Compare with factory specifications.
  19. Adjust Freon metering control device per factory/manufactures recommendations.
  20. Test and measure air-conditioning system for proper production and capacity.
  21. Monitor fan motors and compressor operating temperatures.
  22. Complete and present full written report.

While enrolled in this Agreement; any time you need service you will get Priority Service Scheduling. Absolute Freedom from Diagnostic Charges, you will receive a 15% Discount on any part needed with a full 2 year warranty on parts.

*Additional charge if we supply the filter

All This for a Low Monthly Investment of $14.95

** 2 systems – $14.95 for 1st – additional $9.99 for 2nd – Total = $24.94

Your comfort and complete satisfaction is very important to us. Try this program for ninety days; if you’re not 100% Satisfied you may cancel at anytime.

Oh. Lic. No. 21626